C&K systems System 236i Installation Manual download pdf (Page 2)

SYSTEM 236 Installation Manual

Table of Contents

Subject Page No.

System 236 Terminal Label Front Cover

UL Compliance 2

Installation 2 - 3

Wiring the Panel 3 - 4

System Start-Up 4

Keypad Setup 4 - 5

Addressing Keypads 5

Factory Default Settings 5

Programming Options (Alphabetical List) 5 - 6

Programming the Panel 6 - 7

Programming with the LED Keypad 6

Programming with the Alpha Keypad 6

Entering Hexidecimal Numbers 7

Programming the Alpha Keypad 7 - 8

Programming Letters & Numbers 7

Special Function Keys 8

Programming Options (Numerical Order) 9 - 23

Keypad Label Drawer 24

Telephone Line Problems 24

Watchdog Indicator 25

Keypad Operation Command Summary 25

Help with Common Problems (Troubleshooting) 26 - 27

Reducing False Alarms 28

Warranty Information 28

Programming Worksheets 29 - 32

BEFORE YOU START

Scope of This Manual

This manual contains basic installation and programming information for

the SYSTEM 236 control/communicator. For detailed information about

remote programming, please refer to the Commander II/Monitor II Oper-

ating Manual (P/N 5-051-221-00).

Accuracy

This manual has been carefully checked for accuracy. However, C&K

SYSTEMS assumes no liability for inaccuracies or actions resulting from

the use of this manual. In addition, C&K reserves the right to modify the

SYSTEM 236 hardware, software, and manuals without prior notice.

UL COMPLIANCE

The SYSTEM 236 is in compliance with Underwriters Laboratories, Inc.

Standards UL 985, Household Warning System Units; UL 1023, House-

hold Burglar Alarm System Units; and UL 1635, Digital Burglar Alarm

Communicator System Units. The following programming restric-

tions must be observed to meet UL standards:

UL Compliance (continued)

1. The audible must be programmed to sound at least four

minutes before silencing.

2. No zone may be programmed for silent alarm.

3. Fire zones must be programmed for pulsing audible alarm.

4. Burglar zones must be programmed for a steady audible.

5. Burglar loops (non-24-hour loops) must be programmed

for NO/NC.

6. No Entry Delay may be greater than 45 seconds.

7. No Exit Delay may be greater than 60 seconds.

8. The Dynamic Battery Test must be enabled.

9. The Unit Status Report must be enabled.

10. The 24-hour Check-in must be enabled.

11. No Delay Before Dial may be programmed for the

communicator.

12. The unit must not be programmed to dial a police station.

13. Use screws (supplied) to secure cover or a lock must be

installed on the cabinet.

14. All devices must be UL listed.

15. Loop Response Time must be set to 500mS.

Mounting

The SYSTEM 236 should be mounted in a location which allows conve-

nient access to AC power, telephone connections, and earth ground.

Remove the circuit board from the cabinet. This will prevent

possible damage to the circuit board when removing the knock-

outs.

Remove the knock-outs.

Mark the screw mounting holes on the wall.

INSTALLATION

Mount the cabinet at the desired height and pass the cables

through the knock-outs.

Replace the circuit board, remembering to connect the ground lug

to the lower left corner of the circuit board.

Reconnect the spade lug to the lower door hinge. This provides

the earth ground connection for the door.

Earth Ground

To ensure the effectiveness of the lightning and transient protection

circuits, the control panel must be connected to "Earth Ground". Ideally,

this should be a common ground to the power lines, telephone system, and

security system. This type of ground, called a "Unified Earth Ground",

provides the best protection. The ground connection, from a grounding

rod, cold water pipe or other established ground point, is made to the green

jacketed wire providing a ground to the panel housing.

Zone Programming

FIRE LOOP BURGLAR LOOP

No Delay Before Dial

24-hour arming

Pulsing audible

Supervised

- latching for heat

- resetting for smoke

Not shuntable

NO/NC with EOL

Keypad Requirements

The keypad may not have the EMERGENCY symbol ( ) on it.

If your keypad has this symbol, remove the key and replace it with

one of the blank keys provided.

Steady audible

500mS Loop Response Time

1 2 3 4 5 6 7 ... 27 28

Comments to this Manuals

No comments

C&K systems System 236i Installation Manual Page 2

Comments to this Manuals

Related products and manuals for Numeric keypads C&K systems System 236i